Alcatel SpeedTouch 516(i)/780(WL)

Configuring your network for Electronic Box Services.

Configurer votre réseau pour les services de Electronic Box.

Septembre 2006

[English]

TCP/IP Configuration in Windows XP

1) Click the Start button on your Windows XP Desktop located at the bottom on your left.

2) Right Click with your mouse on the Network Connections Icon

3) Once the Network Connections page open, locate the network device that will be used to communicate with the modem.

Tips: If you are connecting using a network Cable (RJ-45), locate your Local Area Connection icon and proceed with step 3.4. If you are using a wireless adapter like in this example, locate your wireless network connection icon and proceed with step 3.1. Your computer may have problems detecting your network device(s). Please reffer to your computer manufacturer or system supplier for assistance. If you can’t find any network physical device in your system, contact your local hardware supplier or Electronic Box Inc. to purchase a network device such as a wireless network card or a LAN card.

Step 3.1 to 3.3 are for Alcatel SpeedTouch 780(WL) only (skip to step 3.4 for 516(i) modem or if you are connecting using a network Cable).

3.1) Right click on the device and select View Available Wireless Networks.

3.2) Choose Wireless network ‘speedtouchCC5CD2’ Unsecured wireless Network and click on the connect button. If you are already connected, proceed with step 3.3. If your computer can’t connect with the device, verify that your wireless adapter is working properly.

3.3) Once your computer is connected, you should see something like this below

3.4) Select your network adapter that is attached to the modem (select wireless network connection if you already pass through step 3.1, 3.2 and 3.3). Right click on the icon and select properties.

3.5) Locate Internet Protocol (TCP/IP), click on it once and click on the Properties button.

3.6) Select ‘Use the following IP address’ and enter the information below:

Ip address: 192.168.1.60

Subnet mask: 255.255.255.0

Default Gateway: 192.168.1.254

Select ‘Use the following DNS server addresses’

Preferred DNS server: 69.28.239.8

Alternate DNS server: 69.28.239.9

Click on OK

4.0) Open Internet Explorer or your preferred browser. Type the following URL in the Address Bar: http://192.168.1.254

If you are prompt for a login and a password enter the following information:

Password: (leave this field empty)

Click on Ok

You are now inside the modem interface.

4.1) Right click on the Speedtouch tab on the left menu and choose ‘Set Up’ on the bottom of the page.

4.2) Follow the steps in the Easy Setup wizard.

4.2.1) Choose Bridge service if you wish to connect using the Windows XP client (this option is not explained in this tutorial). Select Routed PPP and slick next.

4.2.2) From the drop down box, select VPI/VCI of 0.35 instead of the default 8.35. Leaving the VPI/VCI at 8.35 is incompatible with Electronic Box internet services. Finally, select connection Type PPP Over Ethernet (PPPoE) and click next.

4.2.3) Enter the ADSL User Name and Password that was provided by your sales rep during activation. If you don’t know theses informations, contact Electronic Box immediately. Click Next once your finished with this section.

4.2.4) Enter a special password to prevent unwanted access to the SpeedTouch management interface. We recommand keeping the password that your sales rep provided during activation. Becarefull when choosing a custom password. If you loose the password, nobody can retrace it.

4.2.5) The wizard is now ready to update the changes in the modem. Revise the settings to ensure you entered correctly all the informations before clicking the start button. Once you are ready, click the start button. Wait for the unit to update the changes.

4.2.6) Congratulations you are now connected on the Internet. If your connection is not working, click on the Broadband connection tab and select ‘Internet Services’. Verify the last error messages. If you recently contacted Electronic Box to activate your account, you may see an error message telling ‘Authentication failed’. Please allow 24 hours for processing your activation. If you still have this error message after 24 hours, contact Electronic Box or verify that you correctly entered the value in the wizard. If you have a subnet, continue with step 5.0.

5.0) Your modem is equipt with routing functions allowing subnet routing. Follow theses steps to configure your subnet on your modem.

5.1) Click on the Home Network Tab and select ‘Interfaces’. Click on the LocalNetwork link from the center of the page.

5.2) Once you clicked on the LocalNetwork link, you will be transfered to this page. From here, you can configure your modem to listen on your new subnet. Click on the configure link at the top right corner of the page.

5.3) Enter the first ip address of your subnet available for routing. For example, if your subnet is 64.235.209.232/29, your first available ip addresss would be 64.235.209.233. Enter the subnet mask provided during activation in the second field. Click the add button.

Note: The ip address entered recently will be your new default gateway for your computer network devices attached to the modem unit.

5.4) Click the Start button in Windows Xp, and select Run. Enter the following command: cmd

Click Ok.

5.4.1) Connect to your modem using this command: telnet 192.168.1.254 and press enter.

5.4.2) Enter the login and password you choosed before in the Wizard. The default login is Administrator and the default password field is empty.

Note: We asked to change your password to be the same as the one provided during activation with your sales rep. Reffer to step 4.2.4

5.4.3) Once you are granted in the CLI interface, enter the following command to disable the Nat engine. If you don’t, your modem will continue to translate all your request originating from your local ip with the PPPoE ip address.

nat ifconfig

Press enter

You will now be prompt to enter the interface name. Enter the following informations.

intf= Internet

Press enter

Translation = Disabled

Press enter

5.4.4) Exit the CLI by typing the exit command.

5.5) Congratulation, you are now connected to the internet using your new subnet. Don’t forget to change your tcp/ip settings in windows XP before browsing.

If you still have problems, contact Electronic Box Support Center or write an email to support@electronicbox.net

To configure your SpeedPhone VoIP service, reffer to section 6.0

6.0) This section will explain how to configure your SpeedPhone VoIP service on your ST780(WL). If you are using an ST516(i), please contact Electronic Box.

6.1) Click on the Toolbox tab and select Telephony.

6.2) Click on the configure link on your right at top of the page. Check the Enable Telephony box and click apply.

6.2.1) Clik the Add button and enter the informations provided by Electronic Box.

6.2.2) Enter the SIP Uniform Resource Identifier and all the informations that was provided during activation with your sales rep. Select if you wish to apply this configuration for the port 1, port 2 or both on your modem. Click the apply button.

6.3) Click on the Expert configure link on your right at the top of the page. Enter the registrar IP and all the informations provided during activation with your sales rep. If you don’t know theses informations, contact Electronic Box immediately. Click the apply button once done.

6.4) Click on the details link on your right at the top of the page to view if you are registered on the SIP network. If you are connected, you will see a Gree check mark. If not, a red X will be displayed.

Note: If you recently contacted Electronic Box to activate your account, you may see the red X displayed. Please allow 24 hours for processing your activation. If you still the red X after 24 hours, contact Electronic Box or verify that you correctly entered the value.

6.5) Congratulations, you are now connected to the Digital SpeedPhone Electronic Box Network. Start enjoying low rates long distance calls on your multi-features phone service.